Wanbao Group Compressor Co.,Ltd ( Formerly known as Guangzhou Refrigeration Company Ltd, hereinafter referred as The Co.), started its production in 1987, is the first manufacturer to infroduce foreign technology and equipment for large-scale production of refrigerator compressor in China. In 2014, The Co. acquired the overseas refrigerator compressor manufacturer-Italy ACC, and then founded Italian Wanbao-ACC Co., Ltd. This action upgrades Wanbao compressor from market internationlization towards manufacturing internationalization, and lays solid foundation to brand internationalization for the next step.
The Co. has four production bases in Guangzhou, Qingdao, Hefei, and Italy, with annual production capacity of 26 million units, thus forged a strategic global layout covering both domestic and foreign major customers. Wanbao China mainl supplies to large domestic refrigerator manufacturers including Haier, Hisense, Midea, Meiling, etc, as well as international famous home appliance manufacturers including Electrolux Whirlpool, etc., as their global supplier. Wanbao-ACC Italy is a major supplier of European high-end brand home appliance manufacturers.
www.mbsm.pro , compressor, R134a ,ff16hak ,170 watt ,1/4 HP ,1PH
Category: Solutions,Tester ok
written by Jamila | 6 January 2019
www.mbsm.pro , compressor, R134a ,ff16hak ,170 watt ,1/4 HP ,1PH
Mbsm.pro , LM317 ,Voltage Regulator Pin Outs, Simple test, voltage regulators ics , Voltage regulator
Category: Développement,electronique
written by www.mbsm.pro | 6 January 2019
The LM317 is most commonly found in a TO220 package. It only has three pins and we will be using all of them in this tutorial.
The LM317 Voltage Regulator for Current Control
The use of an LM317 as a constant current source comes right from the data sheet. The schematic below shows how to configure the LM317 as a current regulator. It is the value of R1 that you will be concerned about and that value is determined by the type of LED you are using.
The math is really simple. The factor of 1.25 also comes from the data sheet.
Let’s walk through an example:
Lets say you wanted to control to 300 mA. You would determine that your optimum resistor is: R1 = 1.25 / 0.300 = 4.17 Ohms
Next you’re going to poke around in your box of resistors to see what you’ve got. You probably won’t find that 4.17 Ohm resistor, so you will want to try something close. I had a 4.7 Ohm resistor.
Now you’re going to want to apply the formula to see what that gets you. Current Out = 1.25 / 4.7 = 266 mA.
Finally, we need to do a sanity check of the power rating of the resistor. Here we will use I2 x R to get the power dissipated by the resistor. Power Dissipated by Resistor = 0.2662 x 4.7 = 0.332 Watts (a half watt resistor will do the trick)
Tecumseh, AEZ1410D, compressor, 1/3 HP, r12
Category: compressor
written by Amina | 6 January 2019
Suction gases:
20.0 °C
Overheating:
30.0 K
Hypothermia:
0.00 K
Liquid:
45.0 °C
Refrigerant:
R12
Power supply:
220 – 240V 1~ 50 Hz
Characteristics
Cylinder volume9.4 cm³
Weight11.3kg
Suction line connection7.9 mm – 5/16”
Discharge Line Connection6.4 mm – 1/4”
Power consumption V/Hz/ph200-230V / 50 / 1
Starting current14.0 A
Oil refill0.25 dm3
Type of applicationLow temperature
Compressor seriesAEZ
RefrigerantR12
Maximum operating current2.8A
Evaporation °C
Condensation °C
35
40
45
50
55
60
Pf (Watt)
154
138
121
104
86.9
Pa (W)
191
187
183
179
174
-35
I(A)
1.63
1.63
1.62
1.61
1.6
COP (Watt/W)
0.81
0.74
0.66
0.58
0.5
Pf (Watt)
203
184
164
144
125
105
Pa (W)
203
201
200
198
196
193
-thirty
I(A)
1.65
1.65
1.65
1.65
1.65
1.65
COP (Watt/W)
1
0.91
0.82
0.73
0.64
0.55
Pf (Watt)
264
241
218
194
172
149
Pa (W)
218
219
220
220
220
221
-25
I(A)
1.69
1.69
1.7
1.71
1.71
1.72
COP (Watt/W)
1.21
1.1
0.99
0.88
0.78
0.68
Pf (Watt)
340
311
283
255
228
202
Pa (W)
237
240
243
246
249
251
-20
I(A)
1.74
1.75
1.77
1.78
1.79
1.8
COP (Watt/W)
1.43
1.29
1.16
1.04
0.92
0.8
Pf (Watt)
429
394
359
327
295
264
Pa (W)
260
266
271
276
281
286
-15
I(A)
1.81
1.83
1.85
1.87
1.89
1.91
COP (Watt/W)
1.65
1.48
1.33
1.19
1.05
0.93
Pf (Watt)
532
490
449
409
372
336
Pa (W)
287
294
301
309
316
323
-10
I(A)
1.91
1.93
1.95
1.98
2
2.02
COP (Watt/W)
1.85
1.66
1.49
1.33
1.18
1.04
Pf (W) – Cooling capacity (Watt)
Pa (W) – Power consumption (Watt)
I (A) – Current (A)
COP (W/W) – C.OP (Watt/W)
CV
Watt
1 Porte
2 Portes
Conge-lateur
ASPERA
DANFOSS
EMBRACO
IRE
NECCHI
PRESCOLD
UH
ZEM
ELUX
1/ 12
45
160 l
120 l
90 l
BP 1058 A
TL 2.5 ATL 2.5 B
PW 3.5 K7
AS 14AM 55 ZF
AZ 1320 AAE 12 Z7
E 30101
D 36 ASL 33 AU
1/ 10
56
200 l
160 l
120 l
BP 1072 A
TL 3 ATL 3 B
PW 4.5 F86
B 5A 42PB 6AF 86
ESM 3
AS 12
AE 10 Z7AZ 1328 AAEZ 1332 A
E 36101
L 40 AWL 40 ASL 40 AU
1/ 8
73
220 l
240 l
200 l
BP 1084 A
TL 4 ATL 4 B
PW 4.5 K9
B 8A 43PB 86PB 9AF 88
ESM 4
AS 8
AE 8Z A7AZ 1333 AAZ 1335 AAEZ 1336 A
E 44101 A
L 45 AUL 45 AW
1/ 6
96
400 l
325 l
270 l
BP 1111 ABP 1112 B
TL 5 A
PW 5.5 K11
B 9A 30L 10A 02L 10A 16L 10A 46PB 12AF 90
ESM 5
AS 6AS 66
AE 6Z A7AE 66 ZD7AZ 1340 AAEZ 1343 AAZ 1345 A
E 59101
L 55 AUL 55 AT
1/ 5
127
500 l
410 l
350 l
B 1116 BB 2116 BB 3117 A
FR 7.5 AFR 7.5 BNL 6 A
FF 7.5 BK
L 13A 17L 13A 18L 13A 26L 13B 20L 13A 47
ESM 7
AM 55 ZFAM 5 ZF
AE 5Z F9AZ 1355 DAEZ 1355 DAEZ 1360 AAEZ 1367 A
E 80101 A
L 76 ATL 76 AWL 76 BW
1/ 4
146
600 l
480 l
400 l
B 1118 BB 2118 BB 3119 AE 1121 AE 3121 A
FR 8.5 AFR 8.5 BNL 7 A
FF 8.5 BK
L 16A 01L 16A 25L 16B 22L 17A 34
ESM 8
AM 4C
AE 4Z F11AEZ 1380 AAEZ 1380 B
E 88101 A
L 88 AVL 88 BWL 88 FW
1/ 4
158
800 l
600 l
500 l
FR 10 AFR 10 B
ESM 9
QM 43
1/ 3
230
1200 l
800 l
600 l
FR 11 AFR 11 B
1/ 3
230
1200 l
800 l
600 l
E 1130 BE 2130 BE 3130 BE 4130 B
SC 12 A
ESM 11
AE 1410 AAEZ 1410 DCAE 2410 A
P 12 BWP 12 FW
DANFOSS
223101 1/ 12 CV TL 2.5 A
223102 1/ 10 CV TL 3 A
223103 1/ 8 CV TL 4 A
223104 1/ 6 CV TL 5 A
223105 1/ 5 CV TL 7.5 A
223106 1/ 4 CV TL 8.5 A
223107 1/ 4 CV FR 10 A
223108 1/ 3 CV FR 11 A
223109 1/ 3 CV SC 12 A
Mbsm.pro, Compressor Necchi, Esm5, 1/5 Hp, R12, Replaced by , COMPRESSOR, DANFOSS,TL 5G, 1/6++ (1/5 hp) HP, MBP / HBP -R134a, 220-240V/1/50/60Hz, displacement 5.08 cm3, motor type RSCR
Category: compressor
written by www.mbsm.pro | 6 January 2019
COMPRESSOR TL 5G 1/5 HP
1/6++
R134
230/1/50
DANFOSS
CV
Watt
1 Porte
2 Portes
Conge-lateur
ASPERA
DANFOSS
EMBRACO
IRE
NECCHI
PRESCOLD
UH
ZEM
ELUX
1/ 12
45
160 l
120 l
90 l
BP 1058 A
TL 2.5 ATL 2.5 B
PW 3.5 K7
AS 14AM 55 ZF
AZ 1320 AAE 12 Z7
E 30101
D 36 ASL 33 AU
1/ 10
56
200 l
160 l
120 l
BP 1072 A
TL 3 ATL 3 B
PW 4.5 F86
B 5A 42PB 6AF 86
ESM 3
AS 12
AE 10 Z7AZ 1328 AAEZ 1332 A
E 36101
L 40 AWL 40 ASL 40 AU
1/ 8
73
220 l
240 l
200 l
BP 1084 A
TL 4 ATL 4 B
PW 4.5 K9
B 8A 43PB 86PB 9AF 88
ESM 4
AS 8
AE 8Z A7AZ 1333 AAZ 1335 AAEZ 1336 A
E 44101 A
L 45 AUL 45 AW
1/ 6
96
400 l
325 l
270 l
BP 1111 ABP 1112 B
TL 5 A
PW 5.5 K11
B 9A 30L 10A 02L 10A 16L 10A 46PB 12AF 90
ESM 5
AS 6AS 66
AE 6Z A7AE 66 ZD7AZ 1340 AAEZ 1343 AAZ 1345 A
E 59101
L 55 AUL 55 AT
1/ 5
127
500 l
410 l
350 l
B 1116 BB 2116 BB 3117 A
FR 7.5 AFR 7.5 BNL 6 A
FF 7.5 BK
L 13A 17L 13A 18L 13A 26L 13B 20L 13A 47
ESM 7
AM 55 ZFAM 5 ZF
AE 5Z F9AZ 1355 DAEZ 1355 DAEZ 1360 AAEZ 1367 A
E 80101 A
L 76 ATL 76 AWL 76 BW
1/ 4
146
600 l
480 l
400 l
B 1118 BB 2118 BB 3119 AE 1121 AE 3121 A
FR 8.5 AFR 8.5 BNL 7 A
FF 8.5 BK
L 16A 01L 16A 25L 16B 22L 17A 34
ESM 8
AM 4C
AE 4Z F11AEZ 1380 AAEZ 1380 B
E 88101 A
L 88 AVL 88 BWL 88 FW
1/ 4
158
800 l
600 l
500 l
FR 10 AFR 10 B
ESM 9
QM 43
1/ 3
230
1200 l
800 l
600 l
FR 11 AFR 11 B
1/ 3
230
1200 l
800 l
600 l
E 1130 BE 2130 BE 3130 BE 4130 B
SC 12 A
ESM 11
AE 1410 AAEZ 1410 DCAE 2410 A
P 12 BWP 12 FW
DANFOSS
223101 1/ 12 CV TL 2.5 A
223102 1/ 10 CV TL 3 A
223103 1/ 8 CV TL 4 A
223104 1/ 6 CV TL 5 A
223105 1/ 5 CV TL 7.5 A
223106 1/ 4 CV TL 8.5 A
223107 1/ 4 CV FR 10 A
223108 1/ 3 CV FR 11 A
223109 1/ 3 CV SC 12 A
101GL4550, compressor Secop / Danfoss TL5G, MBP / HBP -R134a, 220-240V/1/50/60Hz, discharge 5.08 cm3, motor type RSCR / CSIR, oil type POE, oil charge 280 cm3, 79 W at -25 / 55° C, LRA 5.7 A, maximum refrigerant charge 400 g, height: 173 mm, weight 7.5 kg
The Copeland RS80C1E-CAZ-252 represents a specialized hermetic reciprocating compressor engineered for low-temperature refrigeration applications where reliability meets efficiency. This single-phase unit operates on R134a refrigerant and delivers consistent performance in demanding freezing environments ranging from -30°C to -10°C evaporating temperatures.
Technical Overview and Application Domain
The RS80C1E-CAZ-252 belongs to Copeland’s proven RS series of hermetic reciprocating compressors, designed specifically for commercial refrigeration applications requiring low back pressure operation. This compressor serves as the heart of various freezing systems including walk-in freezers, ice cream display cabinets, blast freezers, and frozen food storage units where maintaining sub-zero temperatures is critical for product preservation.
Operating at 220-240V single-phase 50Hz power supply, this unit draws approximately 5 amperes during normal operation, making it suitable for standard commercial electrical systems. The RSIR (Resistance Start Induction Run) motor type provides reliable starting characteristics without requiring expensive start capacitors, utilizing instead a simple current relay or PTC (Positive Temperature Coefficient) starting device.
Core Performance Characteristics
This 1 horsepower compressor generates approximately 8,000 BTU/hr cooling capacity when operating at standard LBP (Low Back Pressure) conditions. The displacement volume typically measures around 10.5 cubic centimeters per revolution, allowing the compressor to circulate sufficient refrigerant volume to maintain target evaporator temperatures even under heavy thermal loads.
The hermetic construction means the motor and compression mechanism are sealed within a welded steel shell, protecting internal components from environmental contamination while eliminating the risk of refrigerant leakage through shaft seals. This design philosophy extends operational lifespan and reduces maintenance requirements compared to open or semi-hermetic alternatives.
R134a refrigerant compatibility makes this compressor environmentally friendlier than older R22 units while delivering comparable performance in low-temperature applications. The hydrofluorocarbon (HFC) refrigerant operates with polyolester (POE) lubricating oil, which maintains proper lubrication characteristics across the wide temperature range encountered in LBP freezing applications.
Motor Design and Electrical Configuration
The RSIR motor configuration employs both main (run) and auxiliary (start) windings within the stator assembly. During startup, both windings receive power, creating phase displacement that generates starting torque. Once the motor reaches approximately 75 percent of operating speed, the centrifugal switch or current relay disconnects the start winding, allowing the compressor to continue running on the main winding alone.
This motor type requires lower starting torque compared to CSR (Capacitor Start Run) or CSIR (Capacitor Start Induction Run) designs, making it ideal for applications with lower mechanical resistance during startup. The thermal protection system monitors both motor temperature and current draw, automatically interrupting power if unsafe conditions develop.
The copper winding material provides excellent electrical conductivity and thermal performance. Proper winding insulation ensures reliable operation across the compressor’s operational temperature range, from ambient starting conditions down to the cold temperatures encountered when pumping low-temperature refrigerant vapors.
Refrigeration System Integration
When integrated into complete refrigeration systems, the RS80C1E-CAZ-252 typically connects to evaporator coils operating between -30°C and -10°C saturated suction temperature. The compressor maintains these low evaporator pressures while discharging high-pressure, high-temperature vapor to the condenser at pressures typically ranging from 10 to 15 bar depending on ambient conditions and condenser efficiency.
Proper superheat control becomes critical in low-temperature applications. Maintaining minimum 10°C superheat at the compressor suction prevents liquid refrigerant from entering the compression chamber, which could cause catastrophic damage to valve plates and piston assemblies. Most installations utilize thermostatic expansion valves (TXV) or electronic expansion valves (EEV) to precisely meter refrigerant flow and maintain proper superheat.
The suction line typically measures 1/2 inch ODF (Outside Diameter Flare), while the discharge line uses 3/8 inch ODF connections. Proper suction line sizing prevents excessive pressure drop that would reduce system capacity, while adequate insulation prevents heat gain that increases compression work and reduces efficiency.
Oil Management and Lubrication
The RS80C1E-CAZ-252 ships from the factory charged with approximately 400-450 milliliters of polyolester lubricating oil. POE oil provides superior miscibility with R134a refrigerant, ensuring adequate oil circulation throughout the refrigeration system even at low evaporator temperatures where conventional mineral oils would separate and accumulate.
In low-temperature applications, proper oil return becomes paramount. The suction line must maintain sufficient refrigerant velocity to entrain oil droplets and carry them back to the compressor. Vertical suction risers require minimum 1000 feet per minute velocity at minimum load conditions, often necessitating dual-riser configurations with traps to ensure oil return during light-load operation.
System installations should include oil separators on the discharge line for applications operating below -20°C evaporating temperature. The oil separator removes 95-99 percent of entrained oil from discharge gas before it reaches the condenser, preventing oil accumulation in low-temperature evaporators where viscosity increases and oil return becomes problematic.
Installation Best Practices
Mounting the compressor requires rigid support capable of handling vibration loads during operation. The unit features a quad mounting pattern with bolt holes spaced approximately 8.0 inches by 4.8 inches, standard for this compressor frame size. Rubber isolation grommets between the mounting feet and support structure minimize vibration transmission to surrounding structures.
Electrical connections must match nameplate specifications exactly. The terminal configuration includes common (C), run (R), and start (S) terminals clearly marked on the compressor terminal cover. Wiring should use copper conductors sized according to local electrical codes, typically 14 AWG minimum for this amperage rating with appropriate overcurrent protection.
The starting relay or PTC device mounts directly to the compressor terminal pins or connects via a short wire harness. Current relays work well with RSIR motors, sensing motor current to switch the start winding in and out of the circuit. PTC devices offer simpler installation with fewer components but may require replacement after multiple starting cycles.
Refrigerant Charging Procedures
Initial system evacuation must reach 500 microns or lower before refrigerant charging begins. This deep vacuum removes moisture and non-condensables that could compromise system performance or cause compressor failure through acid formation or reduced heat transfer efficiency.
R134a charging typically follows the superheat method for fixed-orifice systems or subcooling method for TXV-equipped systems. For low-temperature applications with TXV metering, target subcooling ranges from 8-12°C at the condenser outlet, ensuring liquid refrigerant reaches the expansion device without flash gas formation in the liquid line.
Operating pressures vary with ambient conditions and box temperature, but typical LBP systems operate with suction pressures between 0.5-2.0 bar absolute and discharge pressures from 10-14 bar at standard rating conditions. Monitoring both suction and discharge pressures during commissioning ensures proper charge quantity and system operation.
Performance Optimization
Maximizing compressor efficiency requires attention to several system parameters. Maintaining clean condenser coils ensures adequate heat rejection, preventing excessive discharge pressures that increase compression ratio and reduce capacity. Regular coil cleaning schedules keep condensers operating at peak performance.
Evaporator defrost cycles significantly impact low-temperature system operation. Electric defrost, hot gas defrost, or water defrost systems each present different challenges for compressor operation. Proper defrost termination prevents excessive refrigerant migration to the compressor during off-cycles, which could cause liquid slugging during restart.
Suction line accumulators provide additional protection against liquid floodback, particularly during defrost recovery periods when large quantities of liquid refrigerant evaporate rapidly. The accumulator captures liquid refrigerant and meters it back to the compressor at controlled rates, preventing damage while maintaining proper oil return.
Diagnostic Procedures
Monitoring amperage draw provides valuable diagnostic information. Normal running current should match nameplate specifications within 10 percent. Higher amperage indicates excessive discharge pressure from dirty condensers, refrigerant overcharge, or non-condensables in the system. Lower amperage suggests refrigerant undercharge, excessive suction superheat, or internal compressor wear.
Discharge line temperature measurement offers another diagnostic indicator. Excessive discharge temperatures above 110°C indicate low suction superheat, excessive compression ratio, or inadequate motor cooling from low suction gas flow. Installing discharge line temperature sensors enables continuous monitoring and early problem detection.
Suction and discharge pressure measurements combined with refrigerant pressure-temperature charts reveal system operating conditions. Comparing actual temperatures against saturation temperatures calculated from measured pressures identifies problems with superheat, subcooling, refrigerant charge, or airflow across heat exchangers.
Maintenance Requirements
Hermetic compressors require minimal routine maintenance compared to semi-hermetic or open designs. No scheduled oil changes or mechanical seal replacements are necessary. However, monitoring system operation through regular performance checks ensures early problem detection before catastrophic failure occurs.
Filter drier replacement follows manufacturer recommendations, typically annually or whenever system contamination occurs. Low-temperature applications benefit from oversized filter driers that minimize pressure drop while providing adequate moisture and acid removal capacity.
Electrical connections require periodic inspection and tightening to prevent high-resistance connections that generate heat and eventually fail. Terminal cover gaskets should remain intact to prevent moisture ingress that could cause motor winding insulation breakdown.
Troubleshooting Common Issues
Compressor short cycling often results from low refrigerant charge, dirty evaporator coils restricting airflow, or improperly sized thermal overload protection. Systematic diagnosis eliminates potential causes until the root problem is identified and corrected.
Failure to start can indicate electrical problems with the starting relay, PTC device, or motor windings. Checking voltage at the compressor terminals confirms power availability. Testing start and run winding resistance with an ohmmeter identifies open or shorted windings that require compressor replacement.
Excessive noise or vibration suggests mechanical problems within the compressor or inadequate mounting. Internal valve failures, worn piston assemblies, or bearing problems generate abnormal operating sounds. Loose mounting bolts or deteriorated isolation grommets transmit vibration to supporting structures.
Replacement and Cross-Reference Options
When replacement becomes necessary, several equivalent compressor models offer similar performance characteristics. Within the Copeland product line, the RS80C1E-CAV series provides updated refrigerant compatibility for newer low-GWP refrigerants while maintaining similar physical dimensions and capacity.
Environmental Considerations
R134a refrigerant, while significantly better than older CFC and HCFC refrigerants, still carries a global warming potential of 1430. Newer HFO and HFO-blend refrigerants offer substantially lower GWP ratings while delivering comparable performance. Future regulations may require transition to these low-GWP alternatives.
Proper refrigerant recovery during service and end-of-life disposal prevents atmospheric releases. Certified recovery equipment captures refrigerant for recycling or reclamation, complying with environmental regulations while reducing operating expenses through refrigerant reuse.
Energy efficiency impacts environmental footprint throughout compressor operational life. Maintaining peak system efficiency through regular maintenance reduces electricity consumption and associated carbon emissions from power generation.
Safety Considerations
High-pressure refrigeration systems present several safety hazards. Discharge pressures can exceed 15 bar during extreme conditions, capable of rupturing weak components or causing injury if system piping fails. Proper pressure relief devices protect against excessive pressures from abnormal operating conditions.
Electrical safety requires proper grounding of all system components including the compressor. Ground fault protection devices interrupt power if insulation breakdown creates electrical leakage paths that could cause shock or fire hazards.
Refrigerant safety depends on proper handling procedures. While R134a is classified as non-flammable, displacement of oxygen in confined spaces creates asphyxiation risks. Adequate ventilation and refrigerant detection systems protect technicians working with refrigeration equipment.
Advanced System Integration
Modern refrigeration controls enable sophisticated compressor operation strategies. Adaptive defrost systems optimize defrost frequency based on actual frost accumulation rather than fixed time schedules, reducing energy waste and temperature fluctuations.
Variable-speed condenser fans modulate heat rejection capacity to maintain optimal condensing temperatures across varying ambient conditions. This approach prevents excessive subcooling during cool weather while ensuring adequate capacity during peak summer conditions.
Remote monitoring systems track compressor performance parameters continuously, alerting managers to developing problems before failures occur. Cloud-based analytics compare current operation against historical baselines, identifying performance degradation that indicates maintenance needs.
Economic Analysis
The initial investment in quality compressor components pays dividends through extended operational life and reduced maintenance expenses. While premium compressors command higher purchase prices, lower failure rates and longer service intervals deliver superior total cost of ownership.
Energy efficiency directly impacts operating expenses throughout compressor life. A 10 percent efficiency improvement reduces electricity costs proportionally, generating cumulative savings that often exceed initial equipment costs over typical 10-15 year service lives.
Proper system design and installation maximizes return on investment. Oversized or undersized compressors sacrifice efficiency, while poor installation practices create problems that reduce reliability and increase maintenance expenses.
Compressor Replacement Options – Same Refrigerant (R134a)
Model
Brand
HP
BTU/hr
Voltage
Application
RST80C1E-PFV-959
Copeland
1 HP
8,000
208-230V/1/60Hz
LBP/Extended Medium
RS80C1E-CAV-252
Copeland
1 HP
8,250
208-230V/1/60Hz
LBP
AE4460Z-FZ1A
Tecumseh
1 HP
7,900
220-240V/1/50Hz
LBP
NTY65CLX
Embraco
1/4-1/3 HP
7,800
220-240V/1/50Hz
LBP
FR8.5G
Danfoss
1 HP
8,100
220-240V/1/50Hz
LBP
Compressor Replacement Options – Alternative Refrigerants
Model
Brand
Refrigerant
HP
BTU/hr
Voltage
Application
RS80C1E-CAV-224
Copeland
R404A/R407C
1 HP
8,250
208-230V/1/60Hz
LBP
AE4460Y-FZ1A
Tecumseh
R404A
1 HP
8,000
220-240V/1/50Hz
LBP
NJ6226Z
Embraco
R404A
1 HP
8,100
220-240V/1/50Hz
LBP
MTZ64-4VI
Danfoss
R404A/R448A/R449A
1 HP
8,200
220-240V/1/50Hz
LBP
FR8.5CL
Danfoss
R407C
1 HP
7,950
220-240V/1/50Hz
LBP
Comparative Performance Analysis
Understanding how the RS80C1E-CAZ-252 performs relative to competitive offerings helps technicians and engineers make informed equipment selections. The comparison table below highlights key performance differences:
Feature
Copeland RS80
Tecumseh AE4460Z
Embraco NTY65
Danfoss FR8.5G
Cooling Capacity
8,000 BTU/hr
7,900 BTU/hr
7,800 BTU/hr
8,100 BTU/hr
Energy Efficiency (EER)
7.8
7.6
7.5
8.0
Noise Level
52 dB(A)
54 dB(A)
53 dB(A)
51 dB(A)
Weight
18 kg
17.5 kg
16 kg
18.5 kg
Mounting Pattern
8.0″ x 4.8″
8.0″ x 5.0″
7.5″ x 4.5″
8.0″ x 4.8″
Starting Device
Current relay/PTC
Current relay
PTC
Current relay
Warranty Period
3 years
2 years
3 years
3 years
The Copeland RS80C1E-CAZ-252 demonstrates competitive performance across all metrics, with particular strengths in reliability and global service support availability.
System Design Considerations
Proper compressor selection requires matching capacity to application load requirements. Undersized compressors run continuously without achieving target temperatures, while oversized units short-cycle with poor humidity control and reduced efficiency.
Calculating accurate cooling loads accounts for product heat load, infiltration through door openings, transmission through insulated walls, internal lighting and equipment heat, and defrost energy input. Professional load calculation software ensures accurate sizing for reliable system operation.
Condensing unit location affects performance significantly. Outdoor installations experience widely varying ambient temperatures that impact capacity and efficiency. Indoor installations benefit from controlled environments but require adequate ventilation to prevent recirculation of condenser discharge air.
Energy Efficiency Optimization
Energy consumption represents the largest operational expense for most refrigeration systems. Strategic efficiency improvements deliver ongoing savings that accumulate throughout equipment service life.
Variable-speed compressor technology offers substantial efficiency gains compared to fixed-speed units, though reciprocating compressors like the RS80 series utilize on-off cycling rather than speed modulation. Future system upgrades might consider variable-speed scroll or inverter-driven compressors for applications with widely varying loads.
Floating head pressure control adjusts condensing temperature downward during cool ambient conditions, reducing compression ratio and improving efficiency. This strategy requires careful implementation to maintain adequate expansion device pressure differential and oil return velocity.
Heat reclaim systems capture condenser heat for domestic water heating, space heating, or process applications. Recovering waste heat that would otherwise dissipate to ambient improves overall system efficiency while providing useful thermal energy for building operations.
Technological Advancement Trends
Refrigeration compressor technology continues evolving toward higher efficiency, lower environmental impact, and improved reliability. Understanding emerging trends helps plan for future equipment replacements and system upgrades.
Natural refrigerants including CO2, propane, and ammonia gain market acceptance as regulations restrict high-GWP synthetic refrigerants. While the RS80C1E-CAZ-252 operates with R134a, future replacements may utilize low-GWP alternatives like R290 (propane) or R744 (CO2) depending on regulatory requirements.
Internet of Things (IoT) connectivity enables remote monitoring and predictive maintenance strategies. Sensors track compressor performance continuously, comparing current operation against baseline parameters to identify developing problems before failures occur.
Machine learning algorithms analyze operational data patterns to optimize system controls automatically. Adaptive algorithms adjust setpoints, defrost timing, and capacity modulation to minimize energy consumption while maintaining temperature requirements.
Professional Installation Guidelines
Quality installation practices dramatically impact long-term reliability and performance. Following manufacturer specifications and industry best practices ensures optimal results.
Brazing copper refrigerant lines requires flowing dry nitrogen through piping during heating to prevent internal oxide scale formation. Scale particles contaminate the system, causing expansion valve blockages and compressor wear that shorten service life.
Evacuation procedures must achieve deep vacuum levels to remove moisture that causes acid formation and copper plating. Triple evacuation with vacuum breaks accelerates moisture removal compared to single-stage evacuation, particularly important for large systems with extensive piping.
Pressure testing before evacuation identifies leaks while the system contains dry nitrogen rather than expensive refrigerant. Standing pressure tests lasting 24 hours verify joint integrity before proceeding with evacuation and charging procedures.
Professional Recommendations
Field experience with the Copeland RS series demonstrates these compressors deliver reliable performance when properly applied and maintained. The RS80C1E-CAZ-252 suits low-temperature commercial refrigeration applications requiring dependable operation with minimal service requirements.
Technicians should maintain detailed service records documenting operating pressures, temperatures, and amperage readings at each service visit. Trending this data over time reveals performance degradation indicating developing problems before catastrophic failures occur.
Stocking critical replacement components including starting relays, terminal covers with gaskets, and mounting grommets enables rapid repairs that minimize system downtime. For critical applications, maintaining a spare compressor provides insurance against extended outages during compressor failures.
Continuing education on refrigeration fundamentals, new refrigerant technologies, and advanced diagnostic techniques ensures technicians remain current with industry developments. Manufacturer training programs provide valuable insights into proper application and troubleshooting procedures specific to product lines.
Focus Keyphrase: Copeland RS80C1E-CAZ-252 hermetic reciprocating compressor R134a 1HP low temperature freezing LBP refrigeration 220-240V single phase RSIR motor commercial
SEO Title: Copeland RS80C1E-CAZ-252: 1HP R134a Compressor for Commercial Freezing | Complete Technical Guide
Meta Description: Comprehensive technical guide to Copeland RS80C1E-CAZ-252 hermetic reciprocating compressor. 1HP, R134a refrigerant, LBP freezing applications -30°C to -10°C. Installation, maintenance, replacement options.
Excerpt: The Copeland RS80C1E-CAZ-252 represents a specialized hermetic reciprocating compressor engineered for low-temperature refrigeration applications where reliability meets efficiency. This single-phase unit operates on R134a refrigerant and delivers consistent performance in demanding freezing environments ranging from -30°C to -10°C evaporating temperatures. Operating at 220-240V single-phase 50Hz power supply, this unit draws approximately 5 amperes during normal operation, making it suitable for standard commercial electrical systems.
Mbsm.pro, 8HP Open Type 3pH 220V 60Hz Aircooled S4n-8.2y-40p Compressor Condensing Unit
Category: compressor
written by www.mbsm.pro | 6 January 2019
Product Description
Product Description
Product name:
condensing unit
Compressor type:
Semi-hermetic
Application:
Refrigeration Parts
Color:
Green
Brand Name:
Enfriar
Compressor:
8 Hp semi-hermetic compressor
Voltage:
3/220V/60HZ
Refrigerant:
R404A
The compressor is mainly adopts semi-hermetic compressor, .It can also choose other brands of compressors. 1. The use of high-quality copper tube aluminum sheet condenser, large heat exchange area, high heat exchange efficiency; 2. A two-speed low-speed fan is used, and the fan speed can be adjusted according to the change in condensing pressure; 3. Selection of imported refrigeration accessories, complete configuration, good reliability of unit operation; 4. The main electrical components of the electrical unit of the unit adopt Delixi which has multiple protections such as overheating and overload, phase loss, and frequent start prevention; 5. The product structure is divided into integral type and split type, which can meet various needs of customers.
Detailed Images
Air-cooled condenser
1: Use mechanical expansion tube to make copper tube and aluminum fin closely combined, high heat exchange efficiency
2: The motor adopts external rotor motor, high efficiency and energy saving
3: It can be customized in different styles.
Air -Cooled Condensing Units Parts Components
Compressor,Air coolede condenser, Oil separatorGas separator Vibration absorber, filter, solenoid valve, liquid mirror,
reservoir and other parts of conventional units
