Can the GL80 compressor be installed in place of the GL90?
Category: Refrigeration
written by www.mbsm.pro | 12 April 2026
The main difference is the winding material: the GL80 uses aluminum coils, while the GL70 uses copper. Performance-wise, the GL80 is suitable for an upright deep freezer, whereas the GL70 is best for a 12ft double-door refrigerator “The technical difference between the two compressors, manufactured by ZEM or ACC, lies primarily in the horsepower (HP) and displacement volume:
GL80: Has a slightly lower capacity, rated at approximately 1/5 HP
GL90: Typically rated at 1/4 HP (or equivalent, depending on the specific model
Technical Conclusion: Compressor Interchanges
1. Replacing GL80 by GL90 yes 2. Replacing GL90 by GL80 non 3. Replacing GL80 by GL70 non 4. Replacing GL70 by GL80 yes
If you’ve ever opened the back panel of a commercial chest freezer or a light commercial display case and found a compact, brushless compressor with a controller module attached to it, there’s a good chance you were looking at a Danfoss Secop SLV15CNK. This variable-speed hermetic compressor is one of the most widely deployed LBP (Low Back Pressure) units in European and international commercial refrigeration — and for good reason.
Originally built under the Danfoss brand before the compressor division was spun off as Secop GmbH in 2010, the SLV15CNK has carved out a reliable reputation across commercial food retail, light industrial cooling, and even medical cold-chain applications. The unit pictured above — serial reference 561108N4, profile 104H — is the standard 220–240V, 50/60 Hz variant using R290 (propane) refrigerant, one of the most eco-friendly natural refrigerants available today.
Complete Technical Specifications Table
Parameter
Value
Model
SLV15CNK / SLV15CNK.2
Utilisation (MBP/HBP/LBP)
LBP only (Low Back Pressure)
Domain (Freezing/Cooling)
Deep Freezing — evap. temp. –40°C to –10°C
Cooling Wattage at –23°C
~446 W (nominal at standard LBP conditions)
Cubic Feet Cooled
~7–10 ft³ (small to medium chest freezer)
Litres Cooled
~200–280 litres
Kcal/h
~383 Kcal/h
TON
~0.127 TON of refrigeration
Oil Type & Quantity
Polyolester (POE) — 600 cm³
Horsepower (HP)
5/8 HP (~0.60 HP)
Refrigerant Type
R290 (Propane) — max charge 150 g
Power Supply
220–240V / 1Ph / 50–60 Hz (range: 180–254V)
Cooling Capacity BTU
~1521 BTU/h (LBP nominal)
Motor Type
Permanent Magnet (TRI — 3-phase inverter driven)
Displacement
15.28 cm³
Winding Material
Copper (3-phase windings, resistance ~7.7 Ω at 25°C)
Pression Charge
LBP / LST — max condensing temp 55°C (65°C short-term)
Capillary
Approx. 3m / Ø0.31 mm (application-dependent — verify with OEM data)
–40°C to –10°C evaporating; –35°C practical freezer operation
With Fan or Not
Yes — F2 fan cooling required (3.0 m/s airflow on compressor & controller)
Commercial or Domestic
Commercial (light commercial / food retail)
Amperage in Function
Max 4.6 A
LRA (Locked Rotor Amperage)
Electronic cut-off (no traditional LRA — inverter-controlled)
Type of Relay
No traditional relay — uses 105N46xx Series SLV Electronic Controller
Capacitor
No start/run capacitor — inverter-driven (variable speed 2000–4000 RPM)
Country of Origin & Export
Manufactured in Slovakia (Secop GmbH) — exported globally: EU, UK, Middle East, North Africa, Australia, Asia
What Makes This Compressor Special?
Variable Speed Technology
Most technicians encounter fixed-speed compressors day in and day out. The SLV15CNK breaks that mold entirely. It’s a variable speed drive (VSD) compressor, meaning its speed adapts continuously between 2000 and 4000 RPM based on thermal demand. The result is dramatically reduced energy consumption during low-load periods, less mechanical wear, and quieter operation — all things that matter enormously in a commercial food retail environment where a freezer runs 24/7, 365 days a year.
R290 — The Natural Refrigerant Advantage
R290 (propane) is not new, but its adoption in commercial compressors has accelerated rapidly in recent years thanks to its near-zero Global Warming Potential (GWP = 3) compared to the synthetic alternatives it replaces. The SLV15CNK uses a maximum charge of just 150 grams, which keeps it below the safety threshold for flammable refrigerant use in occupied spaces. That tiny charge, combined with propane’s excellent thermodynamic properties, means this compressor achieves high efficiency with a very light environmental footprint.
The Controller Dependency
One detail technicians absolutely must not overlook: this compressor will not function without its dedicated SLV electronic controller (105N46xx series). The label on the unit itself clearly states “Only with SLV controller.” This is not a traditional hermetic compressor you can simply wire up to a relay and a capacitor. The controller handles speed regulation, current protection, speed monitoring, and thermal protection all in one unit. Replacing or sourcing this controller is as important as finding the compressor itself.
Fan Cooling Is Mandatory
At all ambient conditions (32°C, 38°C, and 43°C), the datasheet specifies F2 cooling — meaning fan airflow of at least 3.0 m/s directly on both the compressor body and the electronic controller unit. Attempting to run this compressor without proper forced airflow will trigger thermal protection and lead to premature failure. This is a common oversight when installers replace the compressor without checking the cabinet’s fan arrangement.
Replacement Compressors — Same Gas (R290)
When the SLV15CNK reaches end of life or fails, the most straightforward replacements use the same R290 refrigerant. Here are five proven options:
#
Replacement Model
Brand
Notes
1
SLV15CNK.2 (104H8541)
Secop/Danfoss
Direct drop-in replacement — latest revision
2
SLV12CNK.2
Secop/Danfoss
Slightly lower displacement, same gas and controller family
3
SLV20CNK.2
Secop/Danfoss
Higher capacity option — same R290/controller platform
4
NLV14CNK
Secop/Danfoss
Fixed-speed variant on R290 LBP — requires relay/capacitor
5
SCM10CNX.2
Secop
R290, standard hermetic, LBP — no inverter controller needed
Replacement Compressors — Different Refrigerant
If R290 is not available in your region, or if you’re retro-fitting an older system, here are five equivalents using alternative refrigerants with comparable capacity:
#
Replacement Model
Brand
Refrigerant
Notes
1
SC15G
Secop/Danfoss
R404A / R507A
Classic LBP hermetic, no controller needed
2
NL11MF
Secop/Danfoss
R134a
LBP/MBP, standard hermetic
3
CAJ9513Z
Embraco
R404A
Direct LBP replacement at similar capacity
4
NEBL2134Z
Embraco
R600a
For domestic/light LBP applications
5
MTZ32-4VM
Danfoss
R452A/R404A
Slightly oversized but compatible for retrofits
⚠️ Important: Switching refrigerants requires changing the oil type, capillary tube, and verifying all safety certifications. Always consult the system manufacturer before cross-refrigerant replacement.
Typical Applications — Which Freezers Use This Compressor?
The SLV15CNK is the heart of many products you’ll recognize from the supermarket floor:
AHT Australian series chest freezers (confirmed via MBSM documentation)
Frozen food display cases at petrol stations and convenience stores
Ice cream chest cabinets in retail environments
The AHT connection is particularly well-documented — AHT is a major manufacturer of commercial freezers widely deployed across European and African retail chains, and the SLV15CNK is one of their standard compressor choices.
Installation & Service Notes
A few practical points every technician should keep in mind when working with this unit:
Controller wiring: Always refer to the 105N46xx wiring diagram. Polarity and signal connections matter — the controller is not interchangeable between all SLV variants.
Refrigerant handling: R290 is flammable (Class A3). Work in ventilated areas, avoid open flames, and use an R290-certified manifold gauge set. The 150g charge limit means leaks are rare but must be taken seriously.
Oil compatibility: POE oil is mandatory with R290 in this application. Do not substitute mineral oil or alkylbenzene — POE is pre-filled at the factory at 600 cm³.
Mounting vibration: The compressor ships with rubber mounting grommets. Always re-use or replace them — running on a hard mount increases noise and mechanical fatigue.
Capillary tube: The reference capillary for AHT applications is approximately 3m / 0.31mm diameter, but always measure and verify against the original system before cutting new tubing.
Why This Compressor Matters in 2025 and Beyond
The refrigeration industry is at a turning point. Synthetic refrigerants with high GWP are being phased out under F-Gas regulations in Europe and similar legislation worldwide. The SLV15CNK — running on propane with a permanent magnet variable-speed motor — represents exactly the direction the industry is heading: natural refrigerants, intelligent speed control, and reduced energy consumption without compromising reliability.
For service technicians, understanding this platform deeply isn’t just useful today — it’s preparation for the next decade of commercial refrigeration work.
SEO Title: Embraco EGAS 100HLR Guide: Technical Specs & Field Replacements
Meta Description: Get the breakdown on the Embraco EGAS 100HLR. We cover LRA, R134a specs, displacement, and the best drop-in replacements for this common LBP workhorse.
Excerpt: The Embraco EGAS 100HLR is a staple in domestic refrigeration. This guide provides the raw technical data and equivalent models for fast field swaps.
Field Introduction
You’ll run into the Embraco EGAS 100HLR mostly in standard household refrigerators and large upright freezers. It’s a reliable Low Back Pressure (LBP) unit built for R134a. When these fail, it’s usually a hard start issue or a grounded winding after years of heat cycles. It’s a straightforward swap, but you need to match the displacement and LRA to keep the system balanced.
Technical Specifications Table
Feature
Details
Model
EGAS 100HLR
Brand
Embraco
Refrigerant
R134a
Application
LBP (Low Back Pressure)
Voltage/Frequency
220-240V / 50-60Hz
Phase
1 PH (Single Phase)
LRA (Locked Rotor Amps)
16.9 A (at 60Hz) / 16.0 A (at 50Hz)
Horsepower (HP)
~1/3 HP
Displacement
7.95 cm³
Motor Type
RSIR/CSIR (Depending on starter kit)
Cooling Capacity
~235 – 280 Watts (ASHRAE LBP)
Protection
Thermally Protected
Electrical & Origin Details
Relay Type: Uses a standard PTC or a Current Relay if configured for CSIR.
Capacitor Needs: Usually runs fine without a run capacitor (RSIR), but a start capacitor (approx. 60-80 µF) is often added for high-torque starts.
Manufacturing Origin: Joinville, Brazil (as seen on the nameplate).
Efficiency Metrics (ASHRAE LBP)
Performance changes based on your evaporator temperature. Here’s what to expect:
Evaporating Temp (°C)
Cooling Capacity (Watts)
Power Consumption (Watts)
COP (W/W)
-35
130
145
0.90
-30
185
170
1.09
-25
240
195
1.23
-23.3
265
205
1.29
-20
310
225
1.38
-15
390
255
1.53
Drop-in Replacements
If you can’t source the exact EGAS 100HLR, these models match the displacement and cooling curve for R134a systems:
Embraco: FFI 10HBX or EGYS 100HLP (High Efficiency version).
Secop/Danfoss: TLES10KK.3 or NLE10KK (Ensure R134a compatibility).
Jiaxipera: N1114GZ.
GMCC: SZ90E1H.
Huayi: HYE96YG.
Tecumseh: THG1374YS.
Field Note: Always replace the filter drier and pull a deep vacuum to 500 microns before charging R134a. This model uses POE oil; don’t leave the system open to the atmosphere for longer than necessary.
Huayi HYB35YG (Budget-friendly alternative, Chinese manufacture)
5 Replacements (Other Gas – R600a/R290)
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EG60HLC (R600a – Isobutane, very efficient)
Danfoss SC10CNX (R290 – Propane, modern refrigerant)
Panasonic NR series (R600a – Direct manufacturer alternative)
Secop NL5FT-R600a (R600a conversion variant)
Tecumseh THB4510Z (R600a – High efficiency)
SEO Information
Focus Keyphrase: Panasonic SFH39C73H Compressor Specs and Replacements
SEO Title: Mbsm.pro – Panasonic SFH39C73H Compressor: 1/5 HP R134a Technical Guide
Meta Description: Looking for Panasonic SFH39C73H specs? We break down this 1/5 HP R134a compressor including cooling capacity, wiring, oil type, and the top 10 best replacement models for refrigerator repair.
Excerpt: The Panasonic SFH39C73H is a compact 1/5 HP compressor designed for R134a refrigeration systems, commonly found in domestic refrigerators and small freezers. This guide provides the full technical data sheet, including cooling capacity in Watts and BTU, oil requirements, and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EGU80HLP (R600a – Isobutane, very efficient, 1/6 HP)
Danfoss SC10CNX (R290 – Propane, high efficiency)
Tecumseh CAJ9480Z (R404A – Higher capacity)
Secop NL9FK (R600a compatible variant)
Cubigel HM80AA (R600a – Energy efficient)
Key Features
Thermally protected compressor
Designed for Low Back Pressure (LBP) applications
Suitable for domestic refrigerators up to 280L capacity
RSIR motor type with PTC relay starting
Evaporating temperature range: -25°C to +10°C
Manufactured in China with RoHS compliance
Energy efficient with COP of 1.25
Low noise and vibration operation
Wide voltage range compatibility (187-254V)
Focus Keyphrase: Donper L65CZ1 Compressor Specs and Replacements
SEO Title: Mbsm.pro – Donper L65CZ1 Compressor: 1/5 HP R134a Technical Guide
Meta Description: Looking for L65CZ1 specs? We break down this 1/5 HP R134a Donper compressor including cooling capacity (158-170W), wiring, oil type, and the top replacement models for domestic refrigeration.
Excerpt: The Donper L65CZ1 is a reliable 1/5 HP compressor designed for R134a LBP systems, commonly found in domestic refrigerators and freezers up to 280L capacity. This guide provides the full technical data sheet, including cooling capacity (158-170W at ASHRAE), oil requirements (280-320ml), and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EGU80HLP (R600a – Isobutane, very efficient, 1/6 HP)
Danfoss SC10CNX (R290 – Propane, high efficiency)
Tecumseh CAJ9480Z (R404A – Higher capacity)
Secop NL9FK (R600a compatible variant)
Cubigel HM60AA (R600a – Energy efficient)
Key Features
Thermally protected compressor
Designed for Low Back Pressure (LBP) applications
Suitable for domestic refrigerators up to 250L capacity
RSCR motor type for improved efficiency
Evaporating temperature range: -35°C to -5°C
Manufactured in Singapore with Panasonic quality standards
Energy efficient with COP of 1.35 okmarts.com
Low noise and vibration operation
Compact size and lightweight design
Focus Keyphrase: Panasonic SFK51C94RPX Compressor Specs and Replacements
SEO Title: Mbsm.pro – Panasonic SFK51C94RPX Compressor: 1/6 HP R134a Technical Guide
Meta Description: Looking for SFK51C94RPX specs? We break down this 1/6 HP R134a Panasonic compressor including cooling capacity (157W), wiring, oil type, and the top replacement models for domestic refrigeration.
Excerpt: The Panasonic SFK51C94RPX is a reliable 1/6 HP compressor designed for R134a LBP systems, commonly found in domestic refrigerators and freezers up to 250L capacity. This guide provides the full technical data sheet, including cooling capacity (157W at ASHRAE), oil requirements (280-320ml), and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
Panasonic SFK51C94RPX Compressor Specs and Replacements mbsmpro
Panasonic QB66C13GAX5 Compressor Specs and Replacements
Category: Refrigeration
written by www.mbsm.pro | 12 April 2026
R134a, refrigerant, compressor QB66C13GAX5, 220V 50Hz, LBP, 1/5 hp
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EGU80HLP (R600a – Isobutane, very efficient, 1/6 HP)
Danfoss SC10CNX (R290 – Propane, high efficiency)
Tecumseh CAJ9480Z (R404A – Higher capacity)
Secop NL9FK (R600a compatible variant)
Cubigel HM80AA (R600a – Energy efficient)
Key Features
Thermally protected compressor www.mbsm.pro
Designed for Low Back Pressure (LBP) applications okmarts.com
Suitable for domestic refrigerators up to 250L capacity www.mbsm.pro
RSIR motor type with PTC relay starting okmarts.com
Evaporating temperature range: -35°C to -5°C www.aspneumatic.com
Manufactured in Malaysia with Panasonic quality standards
Energy efficient with COP of 1.19-1.23 www.scribd.com
Low noise and vibration operation
Focus Keyphrase: Panasonic QB66C13GAX5 Compressor Specs and Replacements
SEO Title: Mbsm.pro – Panasonic QB66C13GAX5 Compressor: 1/5 HP R134a Technical Guide
Meta Description: Looking for QB66C13GAX5 specs? We break down this 1/5 HP R134a Panasonic compressor including cooling capacity (165W), wiring, oil type, and the top replacement models for domestic refrigeration.
Excerpt: The Panasonic QB66C13GAX5 is a reliable 1/5 HP compressor designed for R134a LBP systems, commonly found in domestic refrigerators and freezers up to 250L capacity. This guide provides the full technical data sheet, including cooling capacity (165W at ASHRAE), oil requirements (280-320ml), and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EGU90HLP (R600a – Isobutane, very efficient, 1/5 HP)
Danfoss SC10CNX (R290 – Propane, high efficiency)
Tecumseh CAJ9480Z (R404A – Higher capacity)
Secop NL11FK (R600a compatible variant)
Cubigel HM90AA (R600a – Energy efficient)
Focus Keyphrase: SUB COOL GQR80TG Compressor Specs and Replacements
SEO Title: Mbsm.pro – SUB COOL GQR80TG Compressor: 1/4+ HP R134a Technical Guide
Meta Description: Looking for GQR80TG specs? We break down this 1/4+ HP R134a compressor including cooling capacity (400-810W), wiring, oil type, and the top replacement models for commercial refrigeration.
Excerpt: The SUB COOL GQR80TG is a versatile 1/4+ HP compressor designed for R134a MBP/HBP systems, commonly found in commercial coolers and mid-size refrigerators. This guide provides the full technical data sheet, including cooling capacity (400W to 810W depending on conditions), oil requirements (380-420ml POE), and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
Note: Requires complete system flush and expansion valve/capillary adjustment.
Embraco EGU90HLP (R600a – Isobutane, very efficient, 1/5 HP) mbsmpro.com
Tecumseh CAJ9480Z (R404A – Higher capacity)
Danfoss FR8.5CLX (R600a – Propane alternative)
Secop NL11FK (R134a/R600a compatible variant)
Cubigel HM90AA (R600a – Energy efficient)
Key Features
All compressors with individual packaging everwellparts.com
Wide operation range with good voltage adaptability everwellparts.com
Low noise and vibration everwellparts.com
Designed for low back pressure (LBP) applications everwellparts.com
Evaporating temperature range: -34.4°C to -12.2°C (-30°F to 10°F) www.mbsm.pro
Thermally protected mbsmpro.com
CE, IMQ, and IRAM certified www.mbsm.pro
Focus Keyphrase: Tecumseh THG1374YFS Compressor Specs and Replacements
SEO Title: Mbsm.pro – Tecumseh THG1374YFS Compressor: 1/4 HP R134a LBP Technical Guide
Meta Description: Looking for THG1374YFS specs? We break down this 1/4 HP R134a LBP compressor including cooling capacity, wiring, oil type, and the top replacement models for domestic refrigeration.
Excerpt: The Tecumseh THG1374YFS (TH271-FS-316) is a reliable 1/4 HP compressor designed for R134a LBP systems, commonly found in domestic refrigerators and small freezers. This guide provides the full technical data sheet, including cooling capacity in Watts and BTU, oil requirements (243ml POE), and a comprehensive list of compatible replacements for both R134a and modern alternative refrigerants to ensure your repair is successful.
The ZMC GL60AF is a hermetic reciprocating compressor manufactured by Misr Compressor Manufacturing Co. (ZMC) in Egypt, specifically designed for domestic refrigeration applications using R134a refrigerant.
www.pro.mbsm.pro
Technical Specifications Table
Feature
Details
Model
GL60AF
Brand
ZMC (Misr Compressor Manufacturing Co.)
Origin
Made in Egypt
Utilisation
LBP (Low Back Pressure)
Domaine
Domestic Refrigerators & Freezers
Refrigerant Type
R134a
Horsepower (HP)
1/6 HP
Power Supply
200-220V/220-230V ~ 50/60Hz / 1Ph
Voltage Range
170-242V
Displacement
5.99 cm³
Cylinder Diameter
20.88 mm
Stroke
17.48 mm
Cooling Capacity (ASHRAE)
132W at -23.3°C
Cooling Capacity (CECOMAF)
113W at -25°C
Cooling Capacity (kcal/h)
132 kcal/h
Input Power
137-144W
COP (ASHRAE)
1.07 W/W
COP (CECOMAF)
0.82 W/W
EER
0.70-0.91 kcal/Wh
Oil Type
ISO VG 19 ESTER
Oil Charge
270 cm³ (ml)
Motor Type
RSIR (Resistance Start Induction Run)
Net Weight
9.1 kg
Running Current
1.19-1.21A
Locked Rotor Current (LRA)
12.2A
Main Winding Resistance
8.67Ω at 25°C
Start Winding Resistance
18.15Ω at 25°C
Ambient Temperature
43°C
Condensing Temperature
55°C
Evaporating Temp. Range
-25°C to +10°C
Compressor Cooling
Static (Natural)
Application
Household refrigerators, freezers
Test Conditions
Cycle A (CECOMAF):
Evaporating Temperature: -25°C
Condensing Temperature: 55°C
Liquid Temperature entering expansion valve: 55°C
Ambient Temperature: 32°C
Cycle B (ASHRAE):
Evaporating Temperature: -23.3°C
Condensing Temperature: 55°C
Liquid Temperature entering expansion valve: 32°C
Ambient Temperature: 32°C
Efficiency Metrics (COP) Table
Performance varies based on operating conditions. Here is how the GL60AF performs:
Evaporating Temp (°C)
Cooling Capacity (Watts)
Power Consumption (Watts)
COP (W/W)
-25
113
137
0.82
-23.3
132
124
1.07
-20
145
130
1.12
-15
165
138
1.20
-10
190
148
1.28
Replacement Models
Same Brand (ZMC) Equivalent Models:
Model
HP
Application
Refrigerant
Notes
GL60AA
1/6
LBP
R134a
Higher efficiency variant
GL60AH
1/6
LBP
R134a
Enhanced performance model
GL60AN
1/6
LBP
R134a
50Hz optimized version
GL70AA
1/5
LBP
R134a
Slightly larger capacity
Cross-Brand Replacements (R134a):
Brand
Model
HP
Voltage
Notes
Cubigel/ZEM
GL60AA
1/6
220-240V
Direct replacement frigopartners.com
Cubigel
GL60AF
1/6
200-230V
Same specifications iglotech.pl
Electrolux
EGL60AF
1/6
220V
OEM equivalent www.mbsm.pro
Embraco
EMI60HER
1/6
120/220V
Alternative option www.supplyhouse.com
Danfoss/Secop
SC6CL
1/6
220V
Premium alternative
Tecumseh
CAJ4519Z
1/6
220V
Reliable substitute
Alternative Refrigerant Replacements:
Note: Requires complete system flush and expansion device adjustment.
Oil Compatibility: Uses POE (Polyolester) oil – ISO VG 19 grade. Ensure system is clean and dry.
Charging: Refrigerant charge approximately 140g R134a (varies by application). www.mbsm.pro
Starting Device: Requires appropriate RSIR starting relay and capacitor.
Cooling: Static cooling – ensure adequate ventilation around compressor.
Mounting: Use original rubber mounts to minimize vibration.
Focus Keyphrase
ZMC GL60AF Compressor Specs and Replacements
SEO Title
Mbsm.pro – ZMC GL60AF Compressor: 1/6 HP R134a Technical Guide
Meta Description
Looking for ZMC GL60AF specs? We break down this 1/6 HP R134a LBP compressor including cooling capacity, oil type, technical data, and the best replacement models for your refrigerator repair.
The ZMC GL60AF is a reliable 1/6 HP hermetic compressor designed for R134a LBP applications, widely used in domestic refrigerators and freezers. This comprehensive guide provides complete technical specifications including 5.99 cm³ displacement, ISO VG 19 ester oil requirements, 132W cooling capacity, and detailed performance data. Find the best replacement options including Cubigel GL60AA, ZEM equivalents, and modern alternatives for your refrigeration repair needs.